/***********************************************************************//**
 * @file		system_LPC177x_8x.c
 * @brief       CMSIS Cortex-M3 Device Peripheral Access Layer Source File
 *              for the NXP LPC177x_8x Device Series
 * @version     V1.11
 * @date        10. November. 2010
 * @author		NXP MCU SW Application Team
 **************************************************************************
 * Software that is described herein is for illustrative purposes only
 * which provides customers with programming information regarding the
 * products. This software is supplied "AS IS" without any warranties.
 * NXP Semiconductors assumes no responsibility or liability for the
 * use of the software, conveys no license or title under any patent,
 * copyright, or mask work right to the product. NXP Semiconductors
 * reserves the right to make changes in the software without
 * notification. NXP Semiconductors also make no representation or
 * warranty that such application will be suitable for the specified
 * use without further testing or modification.
 **********************************************************************/


#include <stdint.h>
#include "LPC177x_8x.h"
#include "system_LPC177x_8x.h"

/*
//-------- <<< Use Configuration Wizard in Context Menu >>> ------------------
*/
/*--------------------- Clock Configuration ----------------------------------
//
// <e> Clock Configuration
//   <h> System Controls and Status Register (SCS)
//     <o1.0>       EMC_SHIFT: EMC Shift enable
//                     <0=> Static CS addresses match bus width; AD[1] = 0 for 32 bit, AD[0] = 0 for 16+32 bit
//                     <1=> Static CS addresses start at LSB 0 regardless of memory width
//     <o1.1>       EMC_RESET: EMC Reset disable
//                     <0=> EMC will be reset by any chip reset
//                     <1=> Portions of EMC will only be reset by POR or BOR
//     <o1.2>       EMC_BURST: EMC Burst disable
//     <o1.3>       MCIPWR_LEVEL: SD card interface signal SD_PWR Active Level selection
//                     <0=> SD_PWR is active low
//                     <1=> SD_PWR is active high
//     <o1.4>       OSCRANGE: Main Oscillator Range Select
//                     <0=>  1 MHz to 20 MHz
//                     <1=> 15 MHz to 25 MHz
//     <o1.5>       OSCEN: Main Oscillator enable
//   </h>
//
//   <h> Clock Source Select Register (CLKSRCSEL)
//     <o2.0>       CLKSRC: sysclk and PLL0 clock source selection
//                     <0=> Internal RC oscillator
//                     <1=> Main oscillator
//   </h>
//
//   <e3> PLL0 Configuration (Main PLL)
//     <h> PLL0 Configuration Register (PLL0CFG)
//                     <i> PLL out clock = (F_cco / (2 * P))
//                     <i> F_cco = (F_in * M * 2 * P)
//                     <i> F_in  must be in the range of 1 MHz to 25 MHz
//                     <i> F_cco must be in the range of 9.75 MHz to 160 MHz
//       <o4.0..4>   MSEL: PLL Multiplier Selection
//                     <i> M Value
//                     <1-32><#-1>
//       <o4.5..6> PSEL: PLL Divider Selection
//                     <i> P Value
//                     <0=> 1
//                     <1=> 2
//                     <2=> 4
//                     <3=> 8
//     </h>
//   </e>
//
//   <e5> PLL1 Configuration (Alt PLL)
//     <h> PLL1 Configuration Register (PLL1CFG)
//                     <i> PLL out clock = (F_cco / (2 * P))
//                     <i> F_cco = (F_in * M * 2 * P)
//                     <i> F_in  must be in the range of 1 MHz to 25 MHz
//                     <i> F_cco must be in the range of 9.75 MHz to 160 MHz
//       <o6.0..4>   MSEL: PLL Multiplier Selection
//                     <i> M Value
//                     <1-32><#-1>
//       <o6.5..6> PSEL: PLL Divider Selection
//                     <i> P Value
//                     <0=> 1
//                     <1=> 2
//                     <2=> 4
//                     <3=> 8
//     </h>
//   </e>
//
//   <h> CPU Clock Selection Register (CCLKSEL)
//     <o7.0..4>    CCLKDIV: CPU clock (CCLK) divider
//                     <i> 0: The divider is turned off. No clock will be provided to the CPU
//                     <i> n: The input clock is divided by n to produce the CPU clock
//                     <0-31>
//     <o7.8>       CCLKSEL: CPU clock divider input clock selection
//                     <0=> sysclk clock
//                     <1=> PLL0 clock
//   </h>
//
//   <h> USB Clock Selection Register (USBCLKSEL)
//     <o8.0..4>    USBDIV: USB clock (source PLL0) divider selection
//                     <0=> USB clock off
//                     <4=> PLL0 / 4 (PLL0 must be 192Mhz)
//                     <6=> PLL0 / 6 (PLL0 must be 288Mhz)
//     <o8.8..9>    USBSEL: USB clock divider input clock selection
//                     <i> When CPU clock is selected, the USB can be accessed
//                     <i> by software but cannot perform USB functions
//                     <0=> CPU clock
//                     <1=> PLL0 clock
//                     <2=> PLL1 clock
//   </h>
//
//   <h> EMC Clock Selection Register (EMCCLKSEL)
//     <o9.0>       EMCDIV: EMC clock selection
//                     <0=> CPU clock
//                     <1=> CPU clock / 2
//   </h>
//
//   <h> Peripheral Clock Selection Register (PCLKSEL)
//     <o10.0..4>   PCLKDIV: APB Peripheral clock divider
//                     <i> 0: The divider is turned off. No clock will be provided to APB peripherals
//                     <i> n: The input clock is divided by n to produce the APB peripheral clock
//                     <0-31>
//   </h>
//
//   <h> Power Control for Peripherals Register (PCONP)
//     <o11.0>      PCLCD: LCD controller power/clock enable
//     <o11.1>      PCTIM0: Timer/Counter 0 power/clock enable
//     <o11.2>      PCTIM1: Timer/Counter 1 power/clock enable
//     <o11.3>      PCUART0: UART 0 power/clock enable
//     <o11.4>      PCUART1: UART 1 power/clock enable
//     <o11.5>      PCPWM0: PWM0 power/clock enable
//     <o11.6>      PCPWM1: PWM1 power/clock enable
//     <o11.7>      PCI2C0: I2C 0 interface power/clock enable
//     <o11.8>      PCUART4: UART 4 power/clock enable
//     <o11.9>      PCRTC: RTC and Event Recorder power/clock enable
//     <o11.10>     PCSSP1: SSP 1 interface power/clock enable
//     <o11.11>     PCEMC: External Memory Controller power/clock enable
//     <o11.12>     PCADC: A/D converter power/clock enable
//     <o11.13>     PCCAN1: CAN controller 1 power/clock enable
//     <o11.14>     PCCAN2: CAN controller 2 power/clock enable
//     <o11.15>     PCGPIO: IOCON, GPIO, and GPIO interrupts power/clock enable
//     <o11.17>     PCMCPWM: Motor Control PWM power/clock enable
//     <o11.18>     PCQEI: Quadrature encoder interface power/clock enable
//     <o11.19>     PCI2C1: I2C 1 interface power/clock enable
//     <o11.20>     PCSSP2: SSP 2 interface power/clock enable
//     <o11.21>     PCSSP0: SSP 0 interface power/clock enable
//     <o11.22>     PCTIM2: Timer 2 power/clock enable
//     <o11.23>     PCTIM3: Timer 3 power/clock enable
//     <o11.24>     PCUART2: UART 2 power/clock enable
//     <o11.25>     PCUART3: UART 3 power/clock enable
//     <o11.26>     PCI2C2: I2C 2 interface power/clock enable
//     <o11.27>     PCI2S: I2S interface power/clock enable
//     <o11.28>     PCSDC: SD Card interface power/clock enable
//     <o11.29>     PCGPDMA: GPDMA function power/clock enable
//     <o11.30>     PCENET: Ethernet block power/clock enable
//     <o11.31>     PCUSB: USB interface power/clock enable
//   </h>
//
//   <h> Clock Output Configuration Register (CLKOUTCFG)
//     <o12.0..3>   CLKOUTSEL: Clock Source for CLKOUT Selection
//                     <0=> CPU clock
//                     <1=> Main Oscillator
//                     <2=> Internal RC Oscillator
//                     <3=> USB clock
//                     <4=> RTC Oscillator
//                     <5=> unused
//                     <6=> Watchdog Oscillator
//     <o12.4..7>   CLKOUTDIV: Output Clock Divider
//                     <1-16><#-1>
//     <o12.8>      CLKOUT_EN: CLKOUT enable
//   </h>
//
// </e>
*/
#define CLOCK_SETUP           1
#define SCS_Val               0x00000021
#define CLKSRCSEL_Val         0x00000001
#define PLL0_SETUP            1
#define PLL0CFG_Val           0x00000009
#define PLL1_SETUP            1
#define PLL1CFG_Val           0x00000023
#define CCLKSEL_Val           (0x00000001|(1<<8))
#define USBCLK_SETUP		  1
#define USBCLKSEL_Val         (0x00000001|(0x02<<8))
#define EMCCLKSEL_Val         0x00000001
#define PCLKSEL_Val           0x00000002
#define PCONP_Val             0x042887DE
#define CLKOUTCFG_Val         0x00000100


/*--------------------- Flash Accelerator Configuration ----------------------
//
// <e> Flash Accelerator Configuration
//   <o1.12..15> FLASHTIM: Flash Access Time
//               <0=> 1 CPU clock (for CPU clock up to 20 MHz)
//               <1=> 2 CPU clocks (for CPU clock up to 40 MHz)
//               <2=> 3 CPU clocks (for CPU clock up to 60 MHz)
//               <3=> 4 CPU clocks (for CPU clock up to 80 MHz)
//               <4=> 5 CPU clocks (for CPU clock up to 100 MHz)
//               <5=> 6 CPU clocks (for any CPU clock)
// </e>
*/
#define FLASH_SETUP           1
#define FLASHCFG_Val          0x00005000

/*----------------------------------------------------------------------------
  Check the register settings
 *----------------------------------------------------------------------------*/
#define CHECK_RANGE(val, min, max)                ((val < min) || (val > max))
#define CHECK_RSVD(val, mask)                     (val & mask)

/* Clock Configuration -------------------------------------------------------*/
#if (CHECK_RSVD((SCS_Val),       ~0x0000003F))
   #error "SCS: Invalid values of reserved bits!"
#endif

#if (CHECK_RANGE((CLKSRCSEL_Val), 0, 1))
   #error "CLKSRCSEL: Value out of range!"
#endif

#if (CHECK_RSVD((PLL0CFG_Val),   ~0x0000007F))
   #error "PLL0CFG: Invalid values of reserved bits!"
#endif

#if (CHECK_RSVD((PLL1CFG_Val),   ~0x0000007F))
   #error "PLL1CFG: Invalid values of reserved bits!"
#endif

#if (CHECK_RSVD((CCLKSEL_Val),   ~0x0000011F))
   #error "CCLKSEL: Invalid values of reserved bits!"
#endif

#if (CHECK_RSVD((USBCLKSEL_Val), ~0x0000031F))
   #error "USBCLKSEL: Invalid values of reserved bits!"
#endif

#if (CHECK_RSVD((EMCCLKSEL_Val), ~0x00000001))
   #error "EMCCLKSEL: Invalid values of reserved bits!"
#endif

#if (CHECK_RSVD((PCLKSEL_Val), ~0x0000001F))
   #error "PCLKSEL: Invalid values of reserved bits!"
#endif

#if (CHECK_RSVD((PCONP_Val), ~0xFFFEFFFF))
   #error "PCONP: Invalid values of reserved bits!"
#endif

#if (CHECK_RSVD((CLKOUTCFG_Val), ~0x000001FF))
   #error "CLKOUTCFG: Invalid values of reserved bits!"
#endif

/* Flash Accelerator Configuration -------------------------------------------*/
#if (CHECK_RSVD((FLASHCFG_Val), ~0x0000F000))
   #warning "FLASHCFG: Invalid values of reserved bits!"
#endif


/*----------------------------------------------------------------------------
  DEFINES
 *----------------------------------------------------------------------------*/
/* pll_out_clk = F_cco / (2 � P)
   F_cco = pll_in_clk � M � 2 � P */
#define __M                   ((PLL0CFG_Val & 0x1F) + 1)
#define __PLL0_CLK(__F_IN)    (__F_IN * __M)
#define __CCLK_DIV            (CCLKSEL_Val & 0x1F)
#define __PCLK_DIV			  (PCLKSEL_Val & 0x1F)
#define __ECLK_DIV			  ((EMCCLKSEL_Val & 0x01) + 1)

/* Determine core clock frequency according to settings */
#if (CLOCK_SETUP)                       /* Clock Setup                        */

  #if ((CLKSRCSEL_Val & 0x01) == 1) && ((SCS_Val & 0x20)== 0)
   #error "Main Oscillator is selected as clock source but is not enabled!"
  #endif

  #if ((CCLKSEL_Val & 0x100) == 0x100) && (PLL0_SETUP == 0)
   #error "Main PLL is selected as clock source but is not enabled!"
  #endif

  #if ((CCLKSEL_Val & 0x100) == 0)      /* cclk = sysclk */
    #if ((CLKSRCSEL_Val & 0x01) == 0)   /* sysclk = irc_clk */
        #define __CORE_CLK (IRC_OSC / __CCLK_DIV)
		#define __PER_CLK  (IRC_OSC/  __PCLK_DIV)
        #define __EMC_CLK  (IRC_OSC/  __ECLK_DIV)
    #else                               /* sysclk = osc_clk */
        #define __CORE_CLK (OSC_CLK / __CCLK_DIV)
        #define __PER_CLK  (OSC_CLK/  __PCLK_DIV)
        #define __EMC_CLK  (OSC_CLK/  __ECLK_DIV)
    #endif
  #else                                 /* cclk = pll_clk */
    #if ((CLKSRCSEL_Val & 0x01) == 0)   /* sysclk = irc_clk */
        #define __CORE_CLK (__PLL0_CLK(IRC_OSC) / __CCLK_DIV)
        #define __PER_CLK  (__PLL0_CLK(IRC_OSC) / __PCLK_DIV)
        #define __EMC_CLK  (__PLL0_CLK(IRC_OSC) / __ECLK_DIV)
    #else                               /* sysclk = osc_clk */
        #define __CORE_CLK (__PLL0_CLK(OSC_CLK) / __CCLK_DIV)
        #define __PER_CLK  (__PLL0_CLK(OSC_CLK) / __PCLK_DIV)
		#define __EMC_CLK  (__PLL0_CLK(OSC_CLK) / __ECLK_DIV)
    #endif
  #endif

#else
        #define __CORE_CLK (IRC_OSC)
        #define __PER_CLK  (IRC_OSC)
        #define __EMC_CLK  (IRC_OSC)
#endif

/*----------------------------------------------------------------------------
  Clock Variable definitions
 *----------------------------------------------------------------------------*/
uint32_t SystemCoreClock = __CORE_CLK;/*!< System Clock Frequency (Core Clock)*/
uint32_t PeripheralClock = __PER_CLK; /*!< Peripheral Clock Frequency (Pclk)  */
uint32_t EMCClock		 = __EMC_CLK; /*!< EMC Clock Frequency 				  */
uint32_t USBClock 		 = (48000000UL);		  /*!< USB Clock Frequency - this value will
									be updated after call SystemCoreClockUpdate, should be 48MHz*/


/*----------------------------------------------------------------------------
  Clock functions
 *----------------------------------------------------------------------------*/
void SystemCoreClockUpdate (void)            /* Get Core Clock Frequency      */
{
  /* Determine clock frequency according to clock register values             */
  if ((LPC_SC->CCLKSEL &0x100) == 0) {            /* cclk = sysclk    */
    if ((LPC_SC->CLKSRCSEL & 0x01) == 0) {    /* sysclk = irc_clk */
          SystemCoreClock = (IRC_OSC / (LPC_SC->CCLKSEL & 0x1F));
          PeripheralClock = (IRC_OSC / (LPC_SC->PCLKSEL & 0x1F));
          EMCClock        = (IRC_OSC / ((LPC_SC->EMCCLKSEL & 0x01)+1));
    }
    else {                                        /* sysclk = osc_clk */
      if ((LPC_SC->SCS & 0x40) == 0) {
          SystemCoreClock = 0;                      /* this should never happen! */
          PeripheralClock = 0;
          EMCClock        = 0;
      }
      else {
          SystemCoreClock = (OSC_CLK / (LPC_SC->CCLKSEL & 0x1F));
          PeripheralClock = (OSC_CLK / (LPC_SC->PCLKSEL & 0x1F));
          EMCClock        = (OSC_CLK / ((LPC_SC->EMCCLKSEL & 0x01)+1));
      }
    }
  }
  else {                                          /* cclk = pll_clk */
    if ((LPC_SC->PLL0STAT & 0x100) == 0) {        /* PLL0 not enabled */
          SystemCoreClock = 0;                      /* this should never happen! */
          PeripheralClock = 0;
          EMCClock 		  = 0;
    }
    else {
      if ((LPC_SC->CLKSRCSEL & 0x01) == 0) {    /* sysclk = irc_clk */
          SystemCoreClock = (IRC_OSC * ((LPC_SC->PLL0STAT & 0x1F) + 1) / (LPC_SC->CCLKSEL & 0x1F));
          PeripheralClock = (IRC_OSC * ((LPC_SC->PLL0STAT & 0x1F) + 1) / (LPC_SC->PCLKSEL & 0x1F));
          EMCClock        = (IRC_OSC * ((LPC_SC->PLL0STAT & 0x1F) + 1) / ((LPC_SC->EMCCLKSEL & 0x01)+1));
      }
      else {                                        /* sysclk = osc_clk */
        if ((LPC_SC->SCS & 0x40) == 0) {
          SystemCoreClock = 0;                      /* this should never happen! */
          PeripheralClock = 0;
          EMCClock 		  = 0;
        }
        else {
          SystemCoreClock = (OSC_CLK * ((LPC_SC->PLL0STAT & 0x1F) + 1) / (LPC_SC->CCLKSEL & 0x1F));
          PeripheralClock = (OSC_CLK * ((LPC_SC->PLL0STAT & 0x1F) + 1) / (LPC_SC->PCLKSEL & 0x1F));
          EMCClock        = (OSC_CLK * ((LPC_SC->PLL0STAT & 0x1F) + 1) / ((LPC_SC->EMCCLKSEL & 0x01)+1));
        }
      }
    }
  }
  /* ---update USBClock------------------*/
  if(LPC_SC->USBCLKSEL & (0x01<<8))//Use PLL0 as the input to the USB clock divider
  {
	  switch (LPC_SC->USBCLKSEL & 0x1F)
	  {
	  case 0:
		  USBClock = 0; //no clock will be provided to the USB subsystem
		  break;
	  case 4:
	  case 6:
		  if(LPC_SC->CLKSRCSEL & 0x01)	//pll_clk_in = main_osc
			  USBClock = (OSC_CLK * ((LPC_SC->PLL0STAT & 0x1F) + 1) / (LPC_SC->USBCLKSEL & 0x1F));
		  else //pll_clk_in = irc_clk
			  USBClock = (IRC_OSC * ((LPC_SC->PLL0STAT & 0x1F) + 1) / (LPC_SC->USBCLKSEL & 0x1F));
		  break;
	  default:
		  USBClock = 0;  /* this should never happen! */
	  }
  }
  else if(LPC_SC->USBCLKSEL & (0x02<<8))//usb_input_clk = alt_pll (pll1)
  {
	  if(LPC_SC->CLKSRCSEL & 0x01)	//pll1_clk_in = main_osc
	  		USBClock = (OSC_CLK * ((LPC_SC->PLL1STAT & 0x1F) + 1));
	  else //pll1_clk_in = irc_clk
	  		USBClock = (IRC_OSC * ((LPC_SC->PLL0STAT & 0x1F) + 1));
  }
  else
	  USBClock = 0; /* this should never happen! */
}

  /* Determine clock frequency according to clock register values             */

/**
 * Initialize the system
 *
 * @param  none
 * @return none
 *
 * @brief  Setup the microcontroller system.
 *         Initialize the System.
 */
void SystemInit (void)
{
#if (CLOCK_SETUP)                       /* Clock Setup                        */
  LPC_SC->SCS       = SCS_Val;
  if (SCS_Val & (1 << 5)) {             /* If Main Oscillator is enabled      */
    while ((LPC_SC->SCS & (1<<6)) == 0);/* Wait for Oscillator to be ready    */
  }

  LPC_SC->CLKSRCSEL = CLKSRCSEL_Val;    /* Select Clock Source for sysclk/PLL0*/

#if (PLL0_SETUP)
  LPC_SC->PLL0CFG   = PLL0CFG_Val;
  LPC_SC->PLL0CON   = 0x01;             /* PLL0 Enable                        */
  LPC_SC->PLL0FEED  = 0xAA;
  LPC_SC->PLL0FEED  = 0x55;
  while (!(LPC_SC->PLL0STAT & (1<<10)));/* Wait for PLOCK0                    */
#endif

#if (PLL1_SETUP)
  LPC_SC->PLL1CFG   = PLL1CFG_Val;
  LPC_SC->PLL1CON   = 0x01;             /* PLL1 Enable                        */
  LPC_SC->PLL1FEED  = 0xAA;
  LPC_SC->PLL1FEED  = 0x55;
  while (!(LPC_SC->PLL1STAT & (1<<10)));/* Wait for PLOCK1                    */
#endif

  LPC_SC->CCLKSEL   = CCLKSEL_Val;      /* Setup Clock Divider                */
  LPC_SC->USBCLKSEL = USBCLKSEL_Val;    /* Setup USB Clock Divider            */
  LPC_SC->EMCCLKSEL = EMCCLKSEL_Val;    /* EMC Clock Selection                */
  LPC_SC->PCLKSEL   = PCLKSEL_Val;      /* Peripheral Clock Selection         */
  LPC_SC->PCONP     = PCONP_Val;        /* Power Control for Peripherals      */
  LPC_SC->CLKOUTCFG = CLKOUTCFG_Val;    /* Clock Output Configuration         */
#endif

#if (FLASH_SETUP == 1)                  /* Flash Accelerator Setup            */
  LPC_SC->FLASHCFG  = FLASHCFG_Val|0x03A;
#endif
#ifdef  __RAM_MODE__
  SCB->VTOR  = 0x10000000 & 0x3FFFFF80;
#else
  SCB->VTOR  = 0x00000000 & 0x3FFFFF80;
#endif
}